E-612, E-661 High Speed, Closed-Loop Piezo Controller for NanoAutomation

E-501.10 Chassis with four E-612.C0 Modules — E-501.10 Chassis with four E-612.C0 High Performance Piezo Controller Modules

OEM Modules and 1 to 4 Channel Bench-Top Versions
Controls Low Voltage Piezo NanoPositioners & Actuators with Integrated Capacitive Displacement Sensors
Opto-Isolation for EMI Immunity
On-Target Signal for higher Throughput
10 µs Parallel Command Port
Integrated Piezo Power Amplifier

E-612.C0 is a high speed parallel command port piezo amplifier with closed-loop feedback servo position controller module for Closed Loop piezo nanopositioning stages, NanoPositioners, and High Performance Piezo Actuators with integrated capacitive displacement sensors.

Standard versions come with a 10 µs/ command 16-bit opto-isolated input port for enhanced EMI immunity. Modified versions without opto-isolation featuring 270 ns response are available on request. An additional-high bandwidth, 0 to 10 V control input is available for analog control.

The E-612.C0 closed-loop servo controller module is also equipped with a Piezo high voltage amplifier providing -20 to 120 V and 80 mA sink and source current.

E-661.CP NanoAutomation Controller — E-661.CP NanoAutomation Closed-Loop Controller and Piezo Driver

E-661.CP is the compact bench-top, stand-alone piezo controller and piezo driver version of the E-612.C0 module. It comes with a metal case for EMI protection and an external power supply.

One to four channel bench-top piezo closed-loop controller versions consisting of an E-501.10 chassis (9.5" rack with power supply) and 1 to 4, E-612.C0 modules are available, too. Control of the multi-channel versions is via one cable (module one, other modules addressed via internal bus) or by connecting each module individually for even faster command throughput (no address select required).

ORDERING INFORMATION:
E-612.C0 High Speed Nano Automation Controller, Opto-Isolated, OEM Board
E-661.CP High Speed Nano Automation Controller, Opto-Isolated, Bench-Top
E-501.10 Bench-top Chassis and Power Supply for 1 to 4, E-612.C0

TECHNICAL DATA: E-612.C0, E-661.CP
Capacitive Sensor Circuit Clock Frequency Bandwidth	100 kHz 1.5 kHz
Amplifier Output Voltage Range Output Power Output Current Current Limitation	-20 to + 120 V 8 W 80 mA (avg. & peak) short-circuit proof (5 minutes, shut-down)
Digital Circuit Data Input level Input Current Timing On-target indication	16 bit TTL 10mA THmin 10 m s TLmin 10 m s Target position ± £ 0.025% to 0.2%, jumper selectable
Analog Input Control Voltage Range Input Impedance	0 to 10 V 10 kW , 1 nF
Sensor Monitor Output Voltage Range Output resistance Bandwidth	-10 to +10 V (jumper selectable) 10 kW 1.5 kHz
Connectors Digital Interface Piezo Sensor Sensor Monitor Analog Input	25 pin D-sub LEMO ERA.00.250 LEMO EPL.00.250 SMB SMB
Power Requirements (external power supply included with E-661.CP)	E-612.C0: +5 V, 0.12 A +15 V, 0.16 A –15 V, 0.16 A +130 V, 80 mA max. –27 V, 80 mA max. E-661.CP: 15 V, 2 A
Dimensions	E-612.C0: Euroboard * E-661.CP: 125 x 50 x 262 mm

* 64 Pin rear connector. Mating extender card: Mod. P-896.00

TECHNICAL DATA: E-501.10
Dimensions Operating Voltage Power Supply P/S Output Voltages Max. Power Consumption Primary Fuse	W: 235, H: 158; D: 288 (see page 6.3) 90-120 VAC, 50-60 Hz 220-264 VAC, 50-60 Hz Linear regulated power supply +130 V, 0.2 A; -27 V, 0.2 A +24 V, 1 A; ± 15 V, 0.5 A +5V, 1 A 50 W 0.63 A slow