E-612.C0, E-661.CP High Speed NanoAutomation Controllers

  • OEM Modules and 1 to 4 Channel Bench-Top Versions
  • Controls Low Voltage Piezo NanoPositioners & Actuators with Integrated Capacitive Displacement Sensors
  • Opto-Isolation for EMI Immunity
  • On-Target Signal for higher Throughput
  • 10 µs Parallel Command Port
  • Integrated Piezo Power Amplifier

 

E-612.C0 is a high speed parallel command port amplifier/position servo controller module for Closed Loop LVPZT Piezo NanoPositioners and Actuators with integrated capacitive displacement sensors.

Standard versions come with a 10 µs/ command 16 bit opto-isolated input port for enhanced EMI immunity. Modified versions without opto-isolation featuring 270 ns response are available on request. An additional-high bandwidth, 0 to 10 V control input is available for analog control.

The E-612.C0 controller module is also equipped with a Piezo voltage amplifier providing -20 to 120 V and 80 mA sink and source current.

E-661.CP is the compact bench-top, stand alone version of the E-612.C0 module. It comes with a metal case for EMI protection and an external power supply.

One to four channel bench-top versions consisting of an E-501.10 chassis (9.5" rack with power supply) and 1 to 4, E-612.C0 modules are available, too. Control of the multi-channel versions is via one cable (module one, other modules addressed via internal bus) or by connecting each module individually for even faster command throughput (no address select required).


ORDERING INFORMATION:
E-612.C0 High Speed Nano Automation Controller, Opto-Isolated, OEM Board
E-661.CP High Speed Nano Automation Controller, Opto-Isolated, Bench-Top
E-501.10 Bench-top Chassis and Power Supply for 1 to 4, E-612.C0

 

 

TECHNICAL DATA: E-612.C0, E-661.CP
Capacitive Sensor Circuit
Clock Frequency
Bandwidth

100 kHz
1.5 kHz

Amplifier
Output Voltage Range
Output Power
Output Current
Current Limitation

-20 to + 120 V
8 W
80 mA (avg. & peak)
short-circuit proof
(5 minutes, shut-down)

Digital Circuit
Data
Input level
Input Current
Timing

On-target indication

16 bit
TTL
10mA
THmin 10 m s
TLmin 10 m s
Target position ± £ 0.025%
to 0.2%, jumper selectable

Analog Input
Control Voltage Range
Input Impedance

0 to 10 V
10 kW , 1 nF

Sensor Monitor Output
Voltage Range

Output resistance
Bandwidth

-10 to +10 V
(jumper selectable)
10 kW
1.5 kHz

Connectors
Digital Interface
Piezo
Sensor
Sensor Monitor
Analog Input

25 pin D-sub
LEMO ERA.00.250
LEMO EPL.00.250
SMB
SMB
Power Requirements
(external power supply included with E-661.CP)
E-612.C0:
+5 V, 0.12 A
+15 V, 0.16 A
–15 V, 0.16 A
+130 V, 80 mA max.
–27 V, 80 mA max.
E-661.CP:
15 V, 2 A
Dimensions
E-612.C0:
Euroboard *
E-661.CP:
125 x 50 x 262 mm

* 64 Pin rear connector. Mating extender card: Mod. P-896.00

 

 

TECHNICAL DATA: E-501.10

Dimensions

Operating Voltage

Power Supply
P/S Output Voltages


Max. Power Consumption
Primary Fuse

W: 235, H: 158; D: 288
(see page 6.3)
90-120 VAC, 50-60 Hz
220-264 VAC, 50-60 Hz
Linear regulated power supply
+130 V, 0.2 A; -27 V, 0.2 A
+24 V, 1 A; ± 15 V, 0.5 A
+5V, 1 A
50 W
0.63 A slow

 


 

 

E-612.C0 Front Panel

This is a legacy product that may have limited availability or may have been replaced. Ask a PI engineer for an equivalent new model.

Back to Overview